Daniel Schwager
Guest
|
 Posted:
Fri Feb 04, 2005 2:06 pm Post subject:
Probs MSA1000, "I2C_Read_Chunk: Device = EMU, I2C_SetAddress |
|
|
Hi,
we have a problem with a HP MSA1000.
We start to install the MSA1000, but
when conntecting to to CLI we got the following errors
the whole time.
Maybe somebody can help us ?
Do somebody know the meaning of the error (we haven't found it any hp-manuel)
Do somebody know a way to track down this problem ?
Thanks for helping
regards
Danny
| Quote: | Starting ICL links and beginning redundancy negotiation.
PCI ICL link has been enabled.
Starting ICL negotiation . . .
NVRAM Contents:
backplane:
checksum offset = 118
iteration offset = 121
chassis name = VJ
world wide name = 500805F3000005C0
chassis serial num = 9J140000L2GJ
backplane serial num = P3442XAH9HX268
factory:
board serial num = P56350B9IMX0B9
Startup complete.
* MSA1000 Command Line Interface *
CLI> I2C_Read_Chunk: Device = EMU, I2C_SetAddress() failed.
I2C_Read: Resetting I2C bus for device = EMU, retry = 3
I2C_Read_Chunk: Device = EMU, I2C_SetAddress() failed.
I2C_Read: Resetting I2C bus for device = EMU, retry = 2
I2C_Read_Chunk: Device = EMU, I2C_SetAddress() failed.
I2C_Read: Resetting I2C bus for device = EMU, retry = 1
setupICL_Link: failed to receive serial ICL info message.
setupRedundancy: failed to negotiate redundancy.
Redundant controller has been killed.
I2C_Read_Chunk: Device = EMU, I2C_SetAddress() failed.
I2C_Read: Resetting I2C bus for device = EMU, retry = 3
I2C_Read_Chunk: Device = EMU, I2C_SetAddress() failed.
I2C_Read: Resetting I2C bus for device = EMU, retry = 2
I2C_Read_Chunk: Device = EMU, I2C_SetAddress() failed.
I2C_Read: Resetting I2C bus for device = EMU, retry = 1
I2C_Read_Chunk: Device = EMU, I2C_SetAddress() failed.
I2C_Read: Resetting I2C bus for device = EMU, retry = 0
I2C_Read: Device = EMU, I2C_Read_Chunk() failed.
ERROR: failed on do_i2c_emu_command().
|
------------------------------------------------------------
DT Netsolution GmbH - Talaeckerstr. 30 - D-70437 Stuttgart
Tel: +49-711-849910-32 Fax: +49-711-849910-932
WEB: http://www.dtnet.de/ email: daniel.schwager@dtnet.de |
|
Rob Turk
Guest
|
| Posted:
Fri Feb 04, 2005 10:54 pm Post subject:
Re: Probs MSA1000, "I2C_Read_Chunk: Device = EMU, I2C_SetAdd |
|
|
"Daniel Schwager" <Daniel.Schwager@dtnet.de> wrote in message
news:42033B31.FA6CAC@dtnet.de...
| Quote: | Hi,
we have a problem with a HP MSA1000.
We start to install the MSA1000, but
when conntecting to to CLI we got the following errors
the whole time.
Maybe somebody can help us ?
Do somebody know the meaning of the error (we haven't found it any
hp-manuel)
Do somebody know a way to track down this problem ?
Thanks for helping
regards
Danny
* MSA1000 Command Line Interface *
CLI> I2C_Read_Chunk: Device = EMU, I2C_SetAddress() failed.
I2C_Read: Resetting I2C bus for device = EMU, retry = 3
I2C_Read_Chunk: Device = EMU, I2C_SetAddress() failed.
I2C_Read: Resetting I2C bus for device = EMU, retry = 2
I2C_Read_Chunk: Device = EMU, I2C_SetAddress() failed.
I2C_Read: Resetting I2C bus for device = EMU, retry = 1
setupICL_Link: failed to receive serial ICL info message.
setupRedundancy: failed to negotiate redundancy.
Redundant controller has been killed.
|
I2C is a serial protocol inside the machine between chips and subsystems
internally. The message probably means that the internal subsystems can no
longer talk to eachother. That's most likely a hardware failure, so get HP
to service it.
Rob |
|
FAQ
Memberlist
Register
Profile
Log in to check your private messages
Log in